Multi-Tech ISIHI-2S Especificaciones Pagina 80
- Pagina / 188
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
80 MultiModemISI Hybrid Series, ISIHI-2S/2U
Chapter 4—MODEM AT Commands, S-Registers, Result Codes
Flow Control Commands
Flow control refers to techniques used by data terminal equipment and the modem to
pause and resume the flow of information between them. It prevents a device from
accepting more data than it can handle. The modem implements flow control in both
directions. When the modem halts the flow of data, it is called flow control. When the
computer halts the flow, it is called pacing.
&Kn Local Flow Control Selection
n = 0, 3, or 4
Default: &K3
Allows you disable flow control and enable hardware or software flow control.
&K0 completely disables data flow control initiated by the modem. (Same as \Q0.)
&K3 enables modems use of Clear to Send (CTS) signal on the RS-232/V.24 interface to
regulate data flow. When CTS drops, data flow is suspended until the signal goes high
(on) again. This method of flow control works in conjunction with pacing (i.e., computer-
initiated flow control), which uses the Request to Send (RTS) signal on the RS-232/V.24
interface. Hardware flow control cannot be enabled unless an active error correction
protocol is selected. This is the factory default setting. (This is the same as \Q3.)
&K4 enables XON/XOFF software flow control. XON/XOFF flow control is an in-band
method of data flow regulation. In-band data regulation means that the XON (^Q) and
XOFF (^S) characters are inserted into the stream of data rather than using separate
control lines. When an XOFF character is detected, the data stream is suspended until an
XON character is detected. If you issue the &K4 command to the modem, it will respond
to XON/XOFF pacing, and use XON/XOFF characters as its own method of flow control
to the computer. (This is the same as \Q1.)
The drawback to using this method of pacing is that some files may contain these
characters as part of the file data. If such a file is transferred using a modem with XON/
XOFF flow control enabled, the file transfer could fail due to indefinite suspension.
\Qn Local Flow Control Selection
n = 0, 1, or 3
Default: \Q3
Allows you disable flow control and enable hardware or software flow control.
\Q0 completely disables data flow control initiated by the modem. (This is the same as
&K0.)
\Q1 enables XON/XOFF software flow control. XON/XOFF flow control is an in-band
method of data flow regulation. In-band data regulation means that the XON (^Q) and
XOFF (^S) characters are inserted into the stream of data rather than using separate
control lines. When an XOFF character is detected, the data stream is suspended until an
XON character is detected. If you issue the &K4 command to the modem, it will respond
to XON/XOFF pacing, and use XON/XOFF characters as its own method of flow control
to the computer. (This is the same as &K4.)
- MultiModemISI Hybrid Series 1
- Model ISIHI-2S/2U 1
- Contents 3
- Introduction 1 5
- Modem Description/Features 8
- Manual Organization 10
- Chapter 1—Introduction 11
- Technical Specifications 12
- Terminal Adapter 14
- Hardware Installation 2 15
- Before You Start 17
- Installing the ISIHI-2S/2U 18
- LED Indicators 20
- P LED Indicator 21
- D LED Indicator 21
- terminal adapters: 27
- To install 29
- Removing the Driver 32
- IRQ for the card. Click OK 36
- Setting 37
- Optional Settings 48
- ISDN TA Configuration Utility 49
- AT Commands 54
- Removing the Driver (Novell) 56
- Multi_Setup Utility 61
- Administration Utility 64
- Linux Driver Installation 65
- Miscellaneous: 66
- AT Commands, S-Registers 67
- Modem AT Commands 68
- Topic Command Description 70
- Dialing Commands 71
- Dial Modifier Commands 71
- Phone Number Memory Commands 72
- Online Connection Commands 75
- RS-232 Interface Commands 77
- Immediate Action Commands 79
- Flow Control Commands 80
- Escape Sequences 82
- Modem S-Registers 83
- Modem Result Codes 89
- TERMINAL ADAPTER 91
- Terminal Adapter AT Commands 92
- Command Implementation 94
- Switch Configuration Commands 94
- NTER. The dialing string can 102
- Data Call Commands 104
- Terminal Adapter S-Registers 105
- NTER, the escape 107
- Terminal Adapter Result Codes 108
- Making a Call 109
- Modes of Operation 109
- Answering a Call 110
- Hanging Up 110
- Troubleshooting 6 111
- Troubleshooting 112
- Service, Warranty, and 117
- Technical Support/BBS 117
- Introduction 118
- Limited Warranty 118
- Online Warranty Registration 118
- Techical Support 119
- The Multi-Tech BBS 121
- About CompuServe 123
- About the Internet 123
- Appendix 125
- Address Switch Settings 127
- Appendix C: Pin Assignments 129
- Quick Setup Factory Profiles 133
- Quick Setup Example 133
- Loop Qualification 137
- Bearer Service 138
- How To Use AT Commands 162
- Appendix N: Result Codes (TA) 169
- FCC Part 68 Telecom 170
- Industry Canada 171
- FCC Fax Warning 171
- Canadian Limitations Notice 172
- Glossary 173
Relacionado con productos y manuales para Redes Multi-Tech ISIHI-2S
Redes Multi-Tech FR3100 Manual de servicio
(71 paginas)
(71 paginas)
Redes Multi-Tech ISIHI-2S El manual del propietario
(64 paginas)
(64 paginas)
Redes Multi-Tech FR3100 Manual de usuario
(20 paginas)
(20 paginas)
Redes Multi-Tech MT128ISA-UV El manual del propietario
(117 paginas)
(117 paginas)
Philips DCP750-37 manuali
Manuali dei proprietari e guide per l'utente per Video Philips DCP750-37.
We fornisce 2 manuali pdf Philips DCP750-37 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Philips DCP750-37 Manuale Utente (16 pagine)
Marchio: Philips | Categoria: Video | Dimensione: 0.82 MB |
Philips DCP750-37 Manuale Utente (2 pagine)
Marchio: Philips | Categoria: Video | Dimensione: 0.81 MB |
Indice
Più prodotti e manuali per Video Philips
| Modelli | Tipo di Documento |
|---|---|
| 37PFL7332D-37 |
Manuale Utente
 
Philips 37PFL7332D-37 User Manual,
120 pagine
|
| AZ2785 |
Manuale Utente
Philips AZ2785 User Manual,
47 pagine
|
| FW386C-37 |
Manuale Utente
Philips FW386C-37 User Manual,
2 pagine
|
| 27RF50S99 |
Manuale Utente
Philips 27RF50S99 User Manual,
4 pagine
|
| SVD100AT99 |
Manuale Utente
Philips SVD100AT99 User Manual,
1 pagine
|
| VRA641AT |
Manuale Utente
Philips VRA641AT User Manual,
2 pagine
|
| SHS390-28 |
Manuale Utente
Philips SHS390-28 User Manual,
2 pagine
|
| 7FF2FPA-27E |
Manuale Utente
Philips 7FF2FPA-27E User Manual,
16 pagine
|
| DVP2880-F7 |
Manuale Utente
Philips DVP2880-F7 User Manual,
3 pagine
|
| VR810BPH99 |
Manuale Utente
Philips VR810BPH99 User Manual,
83 pagine
|
| S1-00 |
Manuale Utente
Philips S1-00 User Manual,
3 pagine
|
| MCM298-37 |
Manuale Utente
Philips MCM298-37 User Manual,
3 pagine
|
| 201B1074 |
Manuale Utente
Philips 201B1074 User Manual,
93 pagine
|
| 40PFL5505D-F7 |
Manuale Utente
Philips 40PFL5505D-F7 User Manual,
3 pagine
|
| SHE9850-27 |
Manuale Utente
Philips SHE9850-27 User Manual,
3 pagine
|
| 32PFL4908-F7 |
Manuale Utente
Philips 32PFL4908-F7 User Manual,
3 pagine
|
| DVD815AT |
Manuale Utente
Philips DVD815AT User Manual,
2 pagine
|
| DVP3560-F8 |
Manuale Utente
Philips DVP3560-F8 User Manual,
3 pagine
|
| Flat TV 32PF5320 81 cm 32" LCD HDTV monit |
Manuale Utente
Philips Flat TV 32PF5320 81 cm 32" LCD HDTV monitor with Digital Crystal Clear User Manual,
3 pagine
|
| HTL4115B-F7 |
Manuale Utente
Philips HTL4115B-F7 User Manual,
16 pagine
|
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales